Epoxy Injection Grout

Product Details:

Nitobond EP is based on solvent free epoxy resins containingpigments and fi ne fi llers. It is supplied as a two part materialin preweighed quantities for ready onsite mixing and use. Colouredcomponents - white base and green hardener - providevisual evidence that adequate mixing is achieved.

Uses For bonding new cementitious materials to existing cementitious surfaces. For use on horizontal surfaces and on vertical surfaces where mortar or concrete can be supported by formwork. Ideal for extensions and repairs to structural concrete in buildings, loading bays, bridges, roads, bonded or granolithic fl oor toppings etc.

Advantages Nitobond EP can be applied by brush.  More overlay time : Enables to place the concrete upto 6 hrs after applying Nitobond EP, without risk of delamination  High bond strength : Bond strength is more than the tensile strength of good quality concrete  Barrier coat : Acts as a ‘barrier coat’ to the migration of chloride ions from host concrete.

Product Details:

Conbextra EP10 is a solvent free epoxy resin grout designedfor grouting of gap widths of 0.25 to 10mm. It is an all liquidsystem consisting of base and hardener. The components aresupplied in the correct mix proportions designed for whole packmixing on site.

Product Details:

Conbextra EP75 is a solvent free epoxy resin grout designedfor grouting of gap widths of 10 to 75 mm. It is supplied asa three component system consisting of base, hardener andspecially graded aggregate. The components are supplied in thecorrect mix proportions designed for whole pack mixing on site.

Product Details:

Nitobond EP Std is a two component epoxy bonding agentsupplied in pre-weighed quantities for ready on-site mixingand use.
Uses Bonding old and new cementitious substrates.

Advantages ?? Can be applied on concrete & mortar substrate ?? Facilitates improvement in mechanical strength ?? Good positive adhesion 

Application Instructions Preparation All surfaces to be treated must be sound, dust-free and clean. All laitence should be removed by wire-brushing or any other suitable means. Surfaces contaminated with oil or grease, shall be cleaned thoroughly to remove such contaminants.
Mixing The entire contents of the hardener Can should be poured into the resin container and the two materials thoroughly mixed until a uniform colour is obtained. To facilitate application at temperatures below 100 C the separate components should be warmed in hot water to a maximum of 250 C before mixing. Coating Mixed Nitobond EP Std should be brush applied to the prepared substrate. The new concrete should be placed within 3 hours at 350 C to the Nitobond EP Std coated substrate, when it is still in a tacky state. Cleaning Tools and equipment shall be cleaned thoroughly after use with Nitoflor Sol. 

Product Details:

Sikadur®-32 is a solvent-free, two component bonding agent, based on selected epoxy resins.
Uses Sikadur® -32 provides a bond of far greater strength than the tensile strength of the concrete itself. Therefore it is suitable for use as a structural bonding agent for : ?? ?? ?? New to existing concrete Mortar Steel, Iron

Characteristics / Advantages ?? ?? ?? ?? ?? ?? Easy to mix and apply Solvent free Unaffected by moisture Highly effective even on damp surface Workable at low temperatures High tensile strength

Product Details:

Brushbond RFX is an high performance elastomeric cementitious coating used for waterproofi ng and to protect atmospherically exposed reinforced concrete structures from attack by acid gases, chloride ions, oxygen & water. Brushbond RFX is suitable for all types of structures including those in coastal environments

Additional Information:

• Delivery Time: SAME DAY
• Packaging Details: 20.088KG

Product Details:

Renderoc Plug is supplied as a ready to use blend of dry powderswhich requires only the addition of clean water at site toproduce a highly consistent, rapid setting mortar which is easyto apply in many diffi cult conditions. The material is basedon a blend of cements, graded aggregates, special fi llers andchemical additives which control the rate of set and minimisethe risk of thermal cracking.

Product Details:

Sikadur®-32 LP is a solvent-free, two component bonding agent, based on selectedepoxy resins. Complies with ASTM C 881-78 type II, Grade 2 Class B+C

Product Details:

Lokfix  is a two-component Epoxy anchoring material, supplied in 3:1 ratio side-by-side cartridges with a static mixer nozzle. When applied it sets and cures rapidly to firmly secure a variety of steel fixings into concrete and solid masonry substrates.Other grades of Lokfix are also available

Product Details:

BASF EPOXY INJECTION GROUTING

Product Details:

Elastic, liquid applied crack bridging, 2 Pack acryliccementitious waterproofing coating system

Additional Information:

• Production Capacity: 50 KG
• Delivery Time: SAME DAY
• Packaging Details: 50 KG

Product Details:

Sikalastic 450 (I) is a single-component; elastomeric, aliphatic polyurethane basedcold liquid applied, high build, waterproof coating system. It cures to form an elastic,seamless, waterproof coating with good crack-bridging properties.

Product Details:

Free fl ow, high strength, non-shrink,cementitious precision grout

Product Details:

Renderoc RG is supplied as a ready to use blend of dry powderswhich requires only the site addition of clean water toproduce a free-fl owing non-shrink repair micro concrete. Thematerial is based on Portland cements, graded aggregatesand fi llers, and additives which impart controlled expansioncharacteristics in the plastic state, while minimising water demand.The low water requirement ensures high early strengthand long-term durability.

Product Details:

Sikadur®-30 LP (IN) is a thixotropic, structural two part adhesive, based on acombination of epoxy resins and especially designed for use at higher temperaturesbetween +25°C and +55°C.

Product Details:

Cebex 100 is an admixture for cementitious grouts where a reduced water/cement ratio and positive expansions are required. Applications include bed grouting, duct grouting, non-shrink infi lling and jointing.

Product Details:

Sika® Injection-201 CE is a very low viscous, elastic and solvent-free polyurethaneinjection resin. In contact with water, a uniform, closed and therefore watertight porestructure forms, which is elastic and flexible

Additional Information:

• Production Capacity: 1 NOS
• Delivery Time: SAME DAY
• Packaging Details: 20.6 KG PACK

Sika MonoTop®-122 F trowelable mortar is a dualshrinkage compensated, thixotropic high strength formulationfor structural concrete repairs. Sika Mono-Top®-122 F is suitable for placing in thicknesses of5mm to 50 mm vertically and 5-15mm overhead.

Additional Information:

• Production Capacity: 1 Bag or More
• Delivery Time: Same Day
• Packaging Details: 30 Kg

Product Details:

SikaGrout VHS is a non-shrink, cementitious precision grout powered byViscoCrete technology. SikaGrout VHS is designed to achieve high early strengthand exceptional ultimate strengths at a fluid consistency. It is nonmetallic andcontains no chlorides

Additional Information:

• Production Capacity: 2000 KG
• Delivery Time: 3 Days
• Packaging Details: 30 KG

Sika® CarboDur® plates are pultruded carbon fibre reinforcedpolymer (CFRP) laminates, designed forstrengthening concrete, timber, masonry, steel andfibre reinforced polymer structures.Sika® CarboDur® plates are bonded onto the structureas externally bonded reinforcement using Sikadur®-30IN epoxy resin based adhesive for normal, or Sikadur®-30 LP epoxy resin based adhesive for elevated temperaturesduring application and / or service.Please refer to the relevant Product Data Sheet formore detailed information about each of these adhesives

Additional Information:

• Minimum Order Quantity: 1 Roll
• Production Capacity: 1
• Delivery Time: SAME DAY AS PER QTY
• Packaging Details: 100 MTR ROLL

Product Details:

Brushcrete is a single component acrylic based polymer whenblended with cement forms a composite polymer modifi edcementitious waterproofi ng system, when used in conjunctionwith fi bre mesh forms a tough hard wearing surface.

Product Details:

Sikadur®-330 (IN) is a two part, thixotropic epoxy based impregnating resin /adhesive.

Product Details:

CICO TAPECRETE P-151, popularly known as TAPECRETE is an acrylic based Polymer Modified Cementitious Flexible Composite coating system. CICO TAPECRETE P-151 in conjunction with cement provides properties to combat the shortcomings of plain cement, particularly its poor adhesion properties, low impact strength, low flexural strength and thin section fragility. CICO TAPECRETE P-151 polymer adds to the potential use as well as enhances the properties of cement slurry/ mortar/concrete making them excellent choice for use in new as well as renovation work.

Product Details:

Sika® Polysulphide  is a cross linking polysulphide based elastic sealantfor vertical and horizontal expansion joints

Product Details:

SikaTop® Seal 107 is a two part acrylic polymer modified cementitious liquid appliedwaterproofing coating system

Product Details:

Sikaflex® Construction+ is a 1-part, moisture curing, elastic joint sealant suitable formovement and connection joints in facades.

Product Details:

Sikadur®-31(IN) is a solvent-free, moisture tolerant, thixotropic, two part structuraladhesive and repair mortar, based on epoxy resins and special fillers, designed foruse at temperatures between +10°C and +40°C.

Product Details:

Latex based Mortar and screed modifi er & bonding agent For modifying and improving bonding of fl oor toppings, renderings and mortars; repair of worn, damaged and spalled concrete, repair of large cracks; polymer modifi ed fl oor screeds; waterproof plasters for masonary and slurries.

Additional Information:

• Delivery Time: SAME DAY
• Packaging Details: 20 LTR

Product Details:

Nitofl or Hardtop Standard is quality controlled, factory blendedpowder which are ready to use on site. They contain specialhardwearing aggregates which have been selected forabrasion and wear resistant properties as well as shape andsize. These latter considerations, together with the use ofhigh performance workability admixtures, produces a materialwhich is easy to trowel into the surface of fresh, wet concrete.Nitofl or Hardtop Standard cure monolithically to provide adense, non-porous surface which is extremely hardwearingand abrasion resistant. Monolithic cure ensures that problemsnormally associated with thin ‘granolithic’ screeds, viz., shrinkage,cracking, etc., are completely overcome.Being non-metallic, Nitofl or Hardtop Standard provide a nonslipsurface which will never rust and disintegrate.

Product Details:

Crystalline Waterproofing

Product Details:

Sikalastic® 560 is a cold applied , one component waterborne liquid appliedwaterproofing membrane based on modified polyurethane

Product Details:

We are engaged in wholesaling trading and service providing a high grade range of Admixture Concrete Mortar.

Product Details:

Sikadur®-31 C is solvent-free, thixotropic two part epoxy based adhesive forbonding Sikadur®-Combiflex® tape or Sikadur®-Hypalon strip to differentsubstrates.

Product Details:

We provide best quality Nitobond SBR Latex Bonding Agent etc

Product Details:

Soudaflex Construction FC is a high quality, one component polyurethane sealant with high modulus for a wide range of sealing and bonding applications 

Additional Information:

• Delivery Time: 1 DAY
• Packaging Details: 600ML

Product Details:

Brushbond comprises a two component acrylic polymermodified cementitious coating supplied in ready to mix kits.Brushbond can be simply applied by stiff brush, roller, sprayor trowel to obtain the desired texture.Note : For potable water applications, please refer toNitocote CM210 and Brushbond FLX lll datasheets

Product Details:

Oil &Water based modified bituminous primer which penetrates and activates thesubstratesUses Used as a

Product Details:

EXPANSION JOINT TAPE

Product Details:

Reebol is specially formulated blend of mineral oils and chemicalshaving release properties which are superior to those of aconventional mould oil. The chemicals react with the alkali inthe concrete to form a thin water repellent skin on the surfaceof the mould, thereby enabling easy striping from concrete andacting as a protection to steel, aluminium and wooden formwork.Reebol is supplied as Golden Yellow coloured liquid ready fordirect application and use.

Product Details:

Nitozinc Primer is supplied as a two component system basedon metallic zinc and epoxy resin which on mixing gives a greycoloured liquid.

Product Details:

High performance joint sealing system for construction, expansion and connectionjoints as well as for cracks. When fixed to the joint, allows irregular and highmovement in more than one direction, whilst maintaining a high quality seal.
Uses Sealing system for expansion, construction and connection joints, as well as for cracks in:
??? Tunnels and culverts
??? Hydro electric power plants
??? Sewage treatment plants
??? Basements
??? Water retaining structures and drinking water reservoirs
??? Around iron, steel and concrete pipes
??? Swimming pools
Sealing of:
??? Joints with extreme movement
??? Building sections where varying settlement is expected
??? Cracks Repair / reinstatement of leaking joint sealing systems such as:
??? Waterbars
??? Joint sealants etc.
Characteristics / Advantages ??? Advanced adhesion, no activation on site required ??? Use for both cold and hot water applications ??? Easy to install ??? Suitable for both dry and damp concrete surfaces ??? Extremely flexible ??? Performs well within a wide range of temperatures ??? Excellent adhesion to many materials ??? Weather and water resistant ??? Available with normal and rapid hardening grades of adhesive ??? Root resistant ??? Good resistance to many chemicals ??? Versatile system suitable for many difficult situations